Feed Charts

Athena

Blended Feed Schedule							All measurements are in ml per 10L
Mixing Order	Clone		Vegetative				Flowering
Mixing Order	Pre Soak	Feed	Week 1	Week 2	Week 3	Week 4	Week 1	Week 2	Week 3	Week 4	Week 5	Week 6	Week 7	Week 8	Week 9	Week 10 (Flush)
Balance	Use as pH up		*Use as pH up				*Use as pH up
Grow B			29	29	29	29
Grow A			29	29	29	29
Bloom B	13	26					32	32	32	32	26	24	13	11	11
Bloom A	13	26					32	32	32	32	26	24	13	11	11
PK									11	16	24	26	32	26	26
CaMg			8-13	8-13	8-13	8-13	8-13	8-13	8-13	8-13	8-13	8-13	8-13
Cleanse	3	3	5-13	5-13	5-13	5-13	5-13	5-13	5-13	5-13	5-13	5-13	5-13	5-13	5-13	26
EC	1.5	2	2.1	2.1	2.1	2.1	2.3	2.3	2.5	2.6	2.4	2.3	1.7	1.5	1.5	<0.1
PPM 500	750	1000	1050	1050	1050	1050	1150	1150	1250	1300	1200	1150	850	750	750	<50
PPM 700	1050	1400	1470	1470	1470	1470	1610	1610	1750	1820	1680	1610	1190	1050	1050	<70
pH	pH 5.5 - 5.8 EC 2.5 - 3.0		pH 5.5 - 5.8				pH 5.8 - 6.2									pH 6.0 - 6.4

Autoflower Blended Feed Schedule							All measurements are in ml per 10L
Mixing Order	Clone		Vegetative				Flowering
Mixing Order	Pre Soak	Feed	Week 1	Week 2	Week 3	Week 4	Week 5	Week 6	Week 7	Week 8	Week 9	Week 10	Week 11 (Flush)
Balance	Use as pH up		*Use as pH up				*Use as pH up
Grow B			8	16	16	16
Grow A			8	16	16	16
Bloom B							16	16	16
Bloom A							16	16	16
PK							8	12	13	16	13	13
CaMg			8-13	8-13	8-13	8-13	8-13	8-13	8-13
Cleanse	3	3	5-13	5-13	5-13	5-13	5-13	5-13	5-13	5-13	5-13	5-13	26
EC
PPM 500
PPM 700
pH	pH 5.5 - 5.8 EC 2.5 - 3.0		pH 5.5 - 5.8				pH 5.8 - 6.2						pH 6.0 - 6.4

Growers Notes

These are recommendations based upon our extensive testing. Every situation is unique and requires the grower to monitor plant health and adapt the recipe according to crop response.

Best Practices

Shake well before use – Our products run through a 1 micron filter before bottling so any micro-particles you may see won’t clog dosing systems or emitters
Use clean measuring instruments – do not put anything into the bottle to avoid contamination
To increase target EC – Always use equal parts A & B to maintain mineral balance
DO NOT combine products in undiluted form – This renders the formulas useless and must be disposed of
Store closed in original packaging – Keep at a temperature between 7° C and 30° C. Exposure to the environment will reduce shelf-life
Adjust recipe as needed – Every cultivar and growing environment is unique. Adjust accordingly to maintain plant health and vigour

RDWC and Other Recirculating Hydroponics Systems:

Any recirculating or deep water culture (DWC) irrigation system should use Athena Cleanse remove mineral residue and reduce scale.

Using Cleanse in a recirculating or DWC system helps break down materials with lower solubility ratings, such as mineral complexes that are no longer available to plants. Mineral buildup and lockout are major causes of nutrient deficiencies - solve these issues with Athena Cleanse.

CLEANSE

Irrigation System Maintenance

Media/System Flush

Mix 25ml per 10L of water during the final flush to reduce mineral load in media and plant tissue.

Cuttings/Clones

25ml Cleanse per 10L of water. Dip fresh cuttings fully to improve cell health and increase immunity.

Foliar Application

Mix 100ml Cleanse per 1L of water and spray evenly.

Test on a small area first to ensure no damage.

Surface Treatment/Cleaning

Mix 100ml Cleanse per 1L of water and spray all surfaces, tools, floors, and walls maintain a clean and trouble-free environment without toxic and dangerous chemicals.

STACK

Application Timing

Apply Stack from clone up to week 3 of flowering, or once plants stop growing vertically.

Foliar Application

20mL per 10L of water and spray thoroughly twice weekly. Spray with lights off and allow to dry before turning on.

Do not spray past week 3 of flower.

Seed Treatment

Mix 10mL per 10L of water and soak seed for 1-2 minutes before planting. Stack increases germination rates and plant vigour.

IPM

Before application

Shake well before mixing
Turn off fans to ensure even coverage
Turn off lights to reduce risk of damage
Saturate growing media with water

During application

Wear appropriate protective gear (PPE)
Drench the entire plant from stem to leaves

Standard Spray Program							All measurements are ml per Litre
Application Frequency			Vegetative				Flowering
Application Frequency			Week 1	Week 2	Week 3	Week 4	Week 1	Week 2	Week 3
IPM	Preventative (no pests)	2x per week	16-24	16-24	16-24	16-24	16-24	16-24	16-24
IPM	Pressure (some pests)	3x per week	24-32	24-32	24-32	24-32	24-32	24-32	24-32
Stack	Maximise	2x per week	2	2	2	2	2	2	2
Stack	Can be mixed together with IPM

Mildew and Mite Spray Program

All measurements are ml per Litre		Vegetative				Flowering
Application Frequency		Week 1	Week 2	Week 3	Week 4	Week 1	Week 2	Week 3
Preventative (No pests)	Spray 2x per week	15-24	15-24	15-24	15-24	15-24	15-24	15-24
Curative (Some pests)	Spray 3x per week	24-32	24-32	24-32	24-32	24-32	24-32	24-32
Infestation (Infested with pests, possible crop loss)	Spray - 2 Days No spray - 1 Day	Mon	Tue	Wed	Thur	Fri	Sat	Sun
	Repeat above for a 9 day total cycle	32	32	X	32	32	X	32

Infestation / Disease

For spider mite infestations we recommend two consecutive days of spraying followed by a day off. The day off allows the plant to rest because repeated spraying can stress the plant during this process.
If the grower notices any adverse reaction like wilting or other Phytotoxic reactions, they should add more days off between the spray routine. This rotation is repeated 3 times over a 9 day period (the 9th day is a day off)

Fully Saturating the Media

The technique of fully saturating the media first, makes sure the plant is fully hydrated, so that it does not uptake IPM when applied.
Once the spraying is complete, allow the plant to dry down to your normal irrigation schedule and resume your schedule.
If the grower sees any adverse reaction in the plants, stop and take a day or two off before re-applying.

Spray Procedure

Saturate
Fully saturate the media with pH adjusted water.
If the plant is fully hydrated, it will not absorb IPM through its leaves. If the plant is dehydrated, it will absorb IPM through its leaves. Skipping this step can cause burning or phytotoxic reactions.
Climate
Lower temperature to around 22° C and use dehumidifiers to maintain humidity around 55-65% to prevent mould and mildew issues.
Lighting
Only spray when high intensity lights are turned off to prevent burning.
Spray
Start by spraying the media, following up the stalk making sure to drench the undersides of the leaves.
Follow with a spray over the top to ensure full saturation of all plant foliage.
Dry
Allow enough time to dry (3-4 hours) before high intensity lights are turned on.

Fungus Gnat Spray Program

All measurements are ml per Litre		Vegetative				Flowering
Application Frequency		Week 1	Week 2	Week 3	Week 4	Week 1	Week 2	Week 3
Preventative (No pests)	Spray 1x per Week	15-24	15-24	15-24	15-24	15-24	15-24	15-24
Preventative (No pests)	Drench 1x Bi-weekly	X	10	X	10	X	10	X
Curative (Some pests)	Spray 2x per Week	24-32	24-32	24-32	24-32	24-32	24-32	24-32
Curative (Some pests)	Drench 1x per Week	10	10	10	10	10	10	10
Infestation (Infested with pests, possible crop loss)	Run this procedure for 2 weeks	Mon	Tue	Wed	Thur	Fri	Sat	Sun
	Spray	X	24	X	X	24	X	X
	Drench	10	X	X	10	X	X	10

Infestation

For infested root zones , we recommend a day of drench, followed by a day of spray, followed by a day off. The day off allows the plant to rest because drenching and spraying can stress the plant during this process. If the grower notices any adverse reaction like wilting or other phytotoxic reactions, they should add more days off between the drench and spray routine.
This rotation is repeated over a two week period to knock down larvae dwelling in the root-zone and adults in the foliage.
The IPM Drench Procedure is designed to reduce bug pressure enough to get the plants (in that run) to harvest.
Once successful, remove the root zone of all plants and start over.

Flushing the Media

The technique of flushing the media first, make sure the plant is fully hydrated, so that it does not uptake IPM when applied. The final flush removes the IPM from the root zone and gets nutrients back to the roots.
Once the drench is complete, allow the plant to dry down to your normal preference and resume your irrigation schedule.
If the grower sees any adverse reaction in the plants, stop and take a day or two off before re-applying.

Drench Procedure

Saturate
Fully saturate the media with pH adjusted water

Drench
Drench all growing media to runoff with the IPM solution
Wait
Wait 45 min – 1 hour
Flush
Flush again with the appropriate fertiliser for that plant stage

BioBizz Autoflower

Based on a feeding schedule devised by Duck Commander (Autoflower Network)

Soil (Light Mix)					All measurements are in ml per Litre
Mixing Order	Vegetative				Flowering
Mixing Order	Week 1	Week 2	Week 3	Week 4	Week 5	Week 6	Week 7	Week 8	Week 9	Week 10	Week 11 (Flush)
Fish Mix	0.5	1	2	2
Bio Grow					3	3	3	2	2
Bio Bloom					2	2	3	3	3	4
Top Max	0.5	1	1	1	2	2	3	4	4	4
Alg A Mic		1	2	2	3	3	3	3	3
Heaven	0.5	1	2	2	3	3	3	4	4	4
GaMg	0.25	0.25	0.25	0.25	0.25	0.25	0.25

Soil (All Mix)					All measurements are in ml per Litre
Mixing Order	Vegetative				Flowering
Mixing Order	Week 1	Week 2	Week 3	Week 4	Week 5	Week 6	Week 7	Week 8	Week 9	Week 10	Week 11 (Flush)
	1	1	1	1
Bio Grow					1	1	1	1	1
Bio Bloom			1	2	2	3	3	4	4	4
Top Max			1	2	2	3	3	4	4	4
Acti-Vera	2	2	2	2	3	4	4	5	5	5
GaMg	0.25	0.25	0.25	0.25	0.25	0.25	0.25

NPK RAW

Individual Products						Values are in Grams per 4 Litres
	Grow Stage				Fruiting / Flowering Stage
	Week 1	Week 2	Week 3	Week 4	Week 1	Week 2	Week 3	Week 4	Week 5	Week 6	Week 7	Week 8
Nitrogen
Phosphorus
Potassium
Kelp	0.2	0.4	0.4	0.4	0.4	0.4	0.4`	0.4	0.4	0.4	0.4	0.2
Humic Acid	0.2	0.4	0.4	0.4	0.8	0.8	0.8	0.8	0.8	0.8	0.8	0.4
Silica
Yucca	0.3g per 19L	0.3g per 19L	0.3g per 19L	0.3g per 19L	0.3g per 19L	0.3g per 19L	0.3g per 19L	0.3g per 19L	0.3g per 19L	0.3g per 19L	0.3g per 19L	1.2g per 19L
B-Vitamin
Cal / Mag
Full Up
OminA
Cane Molasses
Microbes Grow Stage
Microbes Bloom Stage
Enzymes	0.25	0.25	0.25	0.25	0.25	0.25	0.25	0.25	0.25	0.25	0.25	0.25
Amino Acid	0.6 - 1.25	0.6 - 1.25	0.6 - 1.25	0.6 - 1.25	0.6 - 1.25	0.6 - 1.25	0.6 - 1.25	0.6 - 1.25	0.6 - 1.25	0.6 - 1.25	0.6 - 1.25	0.6 - 1.25

Ideal daytime temperature should be 24-27°C. If using extra CO₂, temps can be 24-30°C
Ideal nighttime temperature should be 19-22°C
Humidity in the grow stage should be approx 60% and in the flowering stage should be approx 50%
Always check pH before adding Microbes and/or feeding your nutrient solution to your plants. Aim for 6.0 pH
PPM of your nutrient solution should be 600-800 in Grow and 800-1000 in Flowering. Some plants may need more that this. Start low and you can always add more fertiliser. It's hard to take it out once it's in your grow medium!
Fertilise 1-2 times per week and use straight water in between, when needed (feed, water, feed (or) feed, water, water, feed)
Soil & CoCo growers should test the PPM's of your runoff after watering. If it is much higher than what you just fed, use less (or no) fertiliser on the next watering. Be careful not to OVER water. If the top 3-5cm of the medium feels dry, it's generally safe to water your plant

Scooba's Cornucopia